Comparative analysis of the properties of composite mortar with addition of rubber powder from worn tires

Comparative analysis of the properties of composite mortar with addition of rubber powder from worn tires

This study compares the performance of two plastering mortars. The first one was produced at a 1:6 proportion of quicklime powder and sand (by volume) and ripened. The second had the same proportion but underwent a water withdrawal process in the oven. The mortars were given the same content of ceme...

Descrizione completa

Salvato in:

Dettagli Bibliografici
Autori principali:	Canova, José Aparecido, Bergamasco, Rosangela, Angelis Neto, Generoso de, Gleize, Philippe Jean Paul
Natura:	Online
Lingua:	por
Pubblicazione:	ANTAC - Associação Nacional de Tecnologia do Ambiente Construído 2012
Accesso online:	https://seer.ufrgs.br/ambienteconstruido/article/view/20515
Tags:	Aggiungi Tag Nessun Tag, puoi essere il primo ad aggiungerne! !

Documenti analoghi

Structural behavior evaluation of precast slabs prototypes made with tire rubber residue concrete
di: Trigo, Ana Paula Moreno, et al.
Pubblicazione: (2008)

Evaluation of rheological properties of mortar with TiO2 addition
di: Dantas, Sérgio Roberto Andrade, et al.
Pubblicazione: (2021)

Shrinkage and the development of mechanical properties in rendering mortars
di: Bastos, Pedro Kopschitz Xavier, et al.
Pubblicazione: (2008)

Sustainability of the housing of the amazon rubber tapper
di: Lima, Valdeci Candido de
Pubblicazione: (2010)

Propriedades nanomecânicas do silicato de cálcio hidratado de síntese
di: Pelisser, Fernando, et al.
Pubblicazione: (2009)

Analysing the logistics impact on the cost composition of a mechanised spraying process of rendering mortar
di: Brandstetter, Maria Carolina Gomes de Oliveira, et al.
Pubblicazione: (2018)

Correlation between modulus of elasticity dynamic and mechanical strengths of cement mortars and sand with lime addition
di: Silva, Narciso Gonçalves da, et al.
Pubblicazione: (2008)

The effectiveness of TiO2 additions to mortar to maintain initial conditions in terms of its reflectance to solar radiation
di: Dantas, Sérgio Roberto Andrade, et al.
Pubblicazione: (2017)

Mechanical properties: wood lumber versus plastic lumber and thermoplastic composites
di: Dias, Bernardo Zandomenico, et al.
Pubblicazione: (2017)

Impact of the mixer and time of mixing on the properties of industrialized mortar
di: Romano, Roberto Cesar de Oliveira, et al.
Pubblicazione: (2009)

Mechanical physical study of concrete substitutes with silica powder exposed in simulated aggressive environment
di: Giménez, Alejandro, et al.
Pubblicazione: (2018)

Rheological characterization of cement paste: association of complementary techniques
di: Betioli, Andrea Murillo, et al.
Pubblicazione: (2009)

Incorporação de lodo calcinado de estação de tratamento de água como material cimentício suplementar
di: Ruviaro, Artur Spat, et al.
Pubblicazione: (2020)

Influence of cement type and water content on the fresh state properties of ready mix mortar
di: Casali, Juliana Machado, et al.
Pubblicazione: (2018)

Influence of polypropylene microfibre (PPMF) dispersion procedure on fresh and hardened rendering mortar properties
di: Dantas, Sérgio Roberto Andrade, et al.
Pubblicazione: (2020)

Learning, composition and placement in the architecture project.
di: Pérgolis, Juan Carlos, et al.
Pubblicazione: (2016)

Índice de Serviço das Calçadas (ISC)
di: Silva, Otavio Henrique da, et al.
Pubblicazione: (2018)

Use of natural additives in construction materials – a review
di: Hernández, Eddisson
Pubblicazione: (2019)

Composite slim floor: elements and construction process
di: Kochem, Raimundo Fagner Freitas, et al.
Pubblicazione: (2018)

Crossed perspectives around the doctorate in architecture.
di: Garric, Jean-Philippe
Pubblicazione: (2015)

BIM and LCA integration proposal using service compositions
di: Silva, Bruno Thiago Rego Valeriano, et al.
Pubblicazione: (2021)

Drying parameters of rendering mortars
di: Salomão, Maria Cláudia de Freitas, et al.
Pubblicazione: (2018)

Study of the influence of the mortar fine recycled aggregate ratio and the mixing sequence on the behavior of new mortars
di: Silva Neto, Gilberto Alves da, et al.
Pubblicazione: (2018)

Use of adherent additives in designing asphalt hot mixtures: a review
di: Vasquez Llamo, Reinerio Elden, et al.
Pubblicazione: (2021)

Digital detailing on the edge: joining of complex curved composite panels
di: Chaszar, Andre
Pubblicazione: (2013)

The Guillermo Bermúdez Umaña’s composition at the Carabelas Building (1969-1972)
di: Güiza-Chaves, Juan Pablo
Pubblicazione: (2021)

Kaufmann desert house. The landscape through the analysis of the architectural composition
di: Rojas Quiñones, Plutarco
Pubblicazione: (2021)

Paradoxical Effects of a Forgotten Subject: Life and Death of Decorative Composition
di: Cravino, Ana María
Pubblicazione: (2020)

High quality of mortar with marble waste aggregate
di: Barbosa, Maria Teresa Gomes, et al.
Pubblicazione: (2018)

Mortar with refractory waste for passive fire protection
di: Lima, Paulo Henrique Pereira, et al.
Pubblicazione: (2020)

Binders, mortars and plasters appropriate to protect the environment.
di: Cedeño Valdiviezo, Alberto
Pubblicazione: (2011)

Environmental and economic perspectives of concrete with high mineral addition content: a case study
di: Isaia, Geraldo Cechella, et al.
Pubblicazione: (2008)

A propos des relations entre nature et ville . Bilan des dialogues franco-lusophones de Tours: es questionnements pour des recherches futures
di: Carrière, Jean-Paul
Pubblicazione: (2020)

The Use of Family Composition and Developed Surface Patterns for an Effective Allocation of Social Housing
di: Vallejos Arcos, Jorge
Pubblicazione: (2000)

Influence of the addition of “synthetic termite saliva” in the compressive strength and water absorption of compacted soil-cement
di: Faria, Obede Borges, et al.
Pubblicazione: (2016)

Comparative study of the chemical additives Consolid 444 and Con-Aid for the improvement of the subgrade in clay soils
di: Guevara Camus, Junior Jeampier, et al.
Pubblicazione: (2023)

Large-Scale Design. Prospects for the Use of Computer-Aided Large-Scale and Fractal Compositions
di: García Alvarado, Rodrigo
Pubblicazione: (1994)

Using ready-mixed mortars in concrete block structural masonry
di: Matos, Paulo Ricardo de, et al.
Pubblicazione: (2020)

Evaluation of early age cracking in rendering mortars with polypropylene fibers
di: Monte, Renata, et al.
Pubblicazione: (2018)

Influence of testing parameters on the determination of the bond strength of mortar renderings
di: Costa, Eliane Betânia Carvalho, et al.
Pubblicazione: (2009)